630 MW机组低压末级长叶片水蚀分析及预防Analysis and Prevention of Water Erosion on Final Stage Blade in Low-pressure Cylinder of 630 MW Units
王维英,李卫军,冯立国,顾正皓,干忠明,马思聪
WANG Weiying,LI Weijun,FENG Liguo,GU Zhenghao,GAN Zhongming,MA Sicong
摘要(Abstract):
大型汽轮机低压缸末几级普遍选用自带冠长叶片,可显著提高汽轮机的性能。随着机组在低负荷工况下运行时间增加,可能出现严重水蚀现象,致使叶冠受损或脱落,威胁机组安全。针对某厂2台630 MW汽轮机组低压缸末级动叶和导流环水蚀故障现象,分析诱发原因,采取对末级动叶进行超音速热喷涂、更换空心静叶、降低8A和8B低压加热器的疏水孔位置、提高低压排汽导流环的强度等综合措施,大幅提高了低压缸的抗水蚀能力。对大型汽轮机组低压缸水蚀进行监测、及时采取综合性的预防措施,可提高机组低压缸的可靠性。
Shrouded blades that are widely used in the final stage of low-pressure cylinder of large steam turbines can significantly improve the performance of the units. After long low-load operation,they are susceptible to water erosion which damages or results in falling off of the tips,and thus threatens the safe operation of the units. In view of the water corrosion failure of the low-pressure last stage blade and guide ring of a 630 MW unit in a power plant,the reasons were analyzed,and measures such as ultrasonic thermal spray of the final stage rotor blade,replacing hollow stator blade,lowering the drain holes of low-pressure heaters 8A and 8B and improving the strength of the low-pressure exhaust guide ring were taken, which greatly improved the water erosion resistance ability of lowpressure cylinder. The preliminary results show that the reliability of low-pressure cylinder of large steam turbine unit can be improved by monitoring the water corrosion of low-pressure cylinder and timely taking comprehensive preventive measures.
关键词(KeyWords):
自带冠叶片;水蚀;喷涂;空心静叶;疏水
shrouded blade;water erosion;spray;hollow stator blade;drainage
基金项目(Foundation): 国网浙江省电力有限公司科技项目(5211DS21003);; 杭州意能电力技术有限公司科技项目(EPRD2020-06)
作者(Author):
王维英,李卫军,冯立国,顾正皓,干忠明,马思聪
WANG Weiying,LI Weijun,FENG Liguo,GU Zhenghao,GAN Zhongming,MA Sicong
参考文献(References):
- [1]刘希涛,张学良.国内外火电汽轮机低压末级长叶片的发展[J]热力透平,2018,47(2):132-139.
- [2]郭永斌,马志强,刘海滨,等.1 000 MW二次再加热机组末级长叶片应用研究[J].神华科技,2018,16(9):50-53.
- [3]王锡辉,何洪浩,李旭,等.湖南省燃煤机组深度调峰问题分析及应对策略[J]湖南电力,2021,41(1):79-82.
- [4]赫广迅,康剑南.火电机组参与灵活性调峰的可行性研究[J]机械工程师,2017,40(9):40-43.
- [5]刘志敏,石永峰.汽轮机低压转子末级叶片断裂分析[J].发电设备,2017,35(4):254-257.
- [6]孙振平,丁佳鹏,单世超,等.核电机组低负荷运行对汽轮机低压末级动叶水蚀的影响[J].汽轮机技术,2019,61(5):292-294.
- [7]刘云锋,李宇峰,王健,等.汽轮机深度调峰的水蚀问题研究[J].发电技术,2021,42(2):473-478.
- [8]薛承感,潘慧斌,丁银萍,等.17-4PH汽轮机叶片激光固溶强化抗汽蚀性能研究[J].动力工程学报,2020,40(1):82-87.
- [9]全威,李松林.激光加工在汽轮机叶片中的应用现状[J].技术加工,2021(3):14-20.
- [10]唐世延,李太江,李巍,等.超音速火焰喷涂抗水蚀涂层应用于核电汽轮机叶片的可行性分析[J].Materials Protection,2016,49(2):58-61.
- [11]叶林,陈国星,胡金力,等.DS和HVOF法制备防水蚀功能涂层的对比研究[J].热喷涂技术,2013,5(1):38-41.
- [12]屈海涛,王智,白娜,等.汽轮机末级空心静叶栅除湿技术研究[J].汽轮机技术,2019,61(2):118-112.
- [13]邹佳生,吴晓明,李亮,等.空心静叶蒸汽加热除湿传热特性的研究[J].西安交通大学学报,2018,52(5):44-49.
- [14]彭国伟,黄元东.导流环结构对低压排汽缸气动性能的影响分析[J].东方电汽评论,2021,137(35):45-48.
- [15]盛晓宇,赖喜德,叶道星,等.不同工况下非对称导流环对排汽缸气动性能的影响[J].汽轮机技术,2021,63(4):284-287.
- [16]崔亚辉,张俊杰,刘亚林,等.高真空下低压转子振动故障处理方案研究及应用[J].汽轮机技术,2018,60(6):453-456.
- [17](俄)亚历山大·雷泽洛维奇著.核电湿蒸汽汽轮机[M].谢永慧,张狄译.西安:西安交通大学出版社,2013,102-103.
- [18]秦华魂.叶片水蚀危险性的分析计算[J].汽轮机技术,2007,49(1):35-36.